Recent Content by Pepper

  1. Pepper
    Post

    Cams and cam removal

    Hey Gary Yes CVMG member as well. I see you have a 1985 vf750 . I think the camshaft issue was sorted out by that time correct? Happy New Years...
    Post by: Pepper, Dec 31, 2019 in forum: 1st & 2nd Generation 1983-1989
  2. Pepper
    Post

    Cams and cam removal

    [ATTACH] [ATTACH] Well she roared back to life just need to put fairings back on sounds fierce again. Thanks For All the help
    Post by: Pepper, Dec 28, 2019 in forum: 1st & 2nd Generation 1983-1989
  3. Pepper
    Post

    Cams and cam removal

    Ok before I close this engine up a question that’s probably been asked a thousand times..... I have the cams re installed at T1-3 all dashes...
    Post by: Pepper, Dec 28, 2019 in forum: 1st & 2nd Generation 1983-1989
  4. Pepper
    Post

    Cams and cam removal

    Thanks yes picked up engine and cams around 90$ Canadian.... if need be I will have camshafts and rocker arms to send to mega cycle at some point....
    Post by: Pepper, Dec 26, 2019 in forum: 1st & 2nd Generation 1983-1989
  5. Pepper
    Post

    Cams and cam removal

    Here is the progress report on the bike. I did call BC and they would redo the cams only not the rocker arms for around $575 Canadian . Went with...
    Post by: Pepper, Dec 25, 2019 in forum: 1st & 2nd Generation 1983-1989
  6. Pepper
    Post

    Cams and cam removal

    Thanks ChunterA I have sent a email off to them as well have you used them before or know of their work?
    Post by: Pepper, Dec 16, 2019 in forum: 1st & 2nd Generation 1983-1989
  7. Pepper
    Post

    Cams and cam removal

    All great points for sure. When I tear into the project I will assess the cams and guides and decide then. thanks for all the help I will...
    Post by: Pepper, Dec 15, 2019 in forum: 1st & 2nd Generation 1983-1989
  8. Pepper
    Post

    Cams and cam removal

    Hey there Lobotomy yes I’ve looked into the megacyclecams They want close to 900$ us for a set. I think that this might be the best option but...
    Post by: Pepper, Dec 14, 2019 in forum: 1st & 2nd Generation 1983-1989
  9. Pepper
    Post

    Hello everyone

    Thanks Randy Yes ticking was a very worn rear exhaust cam had a flat spot on it. So I have weighed all my options the first was to pull and send...
    Post by: Pepper, Dec 13, 2019 in forum: Introductions
  10. Pepper
    Post

    Hello everyone

    Nice bike Laker Yes when I finally was able to buy my first bike it was a 1986 gs400s loved it great size for learning had it for a few years
    Post by: Pepper, Dec 13, 2019 in forum: Introductions
  11. Pepper
    Post

    Hello everyone

    Thanks Steve yes it was my first restoration. This was the bike I wanted in 1983 at the age of 16 lol probs good I didn’t get it then. Cheers
    Post by: Pepper, Dec 11, 2019 in forum: Introductions
  12. Pepper
    Post

    Hello everyone

    Thanks derstuka
    Post by: Pepper, Dec 10, 2019 in forum: Introductions
  13. Pepper
    Post

    Cams and cam removal

    Thanks a lot raYzerman yes the cams at least one is pretty bad.
    Post by: Pepper, Dec 9, 2019 in forum: 1st & 2nd Generation 1983-1989
  14. Pepper
    Thread

    Cams and cam removal

    [ATTACH] [ATTACH] Hi there new to the group I apologize if this has been covered. I have cams that need to be replaced was wondering what’s the...
    Thread by: Pepper, Dec 8, 2019, 20 replies, in forum: 1st & 2nd Generation 1983-1989