Recent Content by mastergregor

  1. mastergregor
    Post

    Help!!! 93 vfr 750 stator

    Has the bike been sitting for a while? If so, gummed up carbs and jets could be a problem. I guess it would be good if you share a bit of history...
    Post by: mastergregor, May 20, 2017 in forum: 3rd & 4th Generation 1990-1997
  2. mastergregor
    Post

    Vfr 800 Fi Interceptor Wont Start

    Hm, not sure I get how it can blow flames through injectors? Can you explain please?
    Post by: mastergregor, Feb 15, 2015 in forum: Mechanics Garage
  3. mastergregor
    Post

    5th gen vfr 800 fi wont idle but runs fine

    You did do a recent sync of throttle bodies and idle speed adjustment, didn't you? :)
    Post by: mastergregor, Feb 15, 2015 in forum: Mechanics Garage
  4. mastergregor
    Post

    '94 that sat for a few years leaking from carb fuel connection

    +1 for rebuilding carbs - you do not want to risk failrure on the road in the middle of nowhere, and with bike sitting for so long, all the seals...
    Post by: mastergregor, Feb 15, 2015 in forum: Mechanics Garage
  5. mastergregor
    Post

    have antifreeze leak mystery

    Get a cooling system pressure tester from your local auto store, usually they will have them as a loaner tool as well. Take radiator cap off, put...
    Post by: mastergregor, Feb 15, 2015 in forum: Mechanics Garage
  6. mastergregor
    Post

    Blown Head Gasket? 6th gen

    Hm, if you had a stuck ring, you would get oil regardless of VTEC engagement. If it happens only with VTEC, intake stem seal might be bad. Water...
    Post by: mastergregor, Oct 10, 2013 in forum: Mechanics Garage
  7. mastergregor
    Post

    5th Gen valve clearance inspection: something looks wrong. Is my cam timing off?

    EvilStig, it DOES look like your cams are off a tooth. You are probably correct, previous owner was adjusting clearance (replacing shims) and did...
    Post by: mastergregor, Oct 1, 2013 in forum: Mechanics Garage
  8. mastergregor
    Post

    Instrument Bulb Replacement Hunt

    A bit late with info, I installed this on my 98 VFR a while back: Amazon.com: HID Xenon Headlight Conversion Kit by Kensun, H4 Dual-Beam...
    Post by: mastergregor, Sep 9, 2013 in forum: 5th Generation 1998-2001
  9. mastergregor
    Post

    Starting issues

    Sometimes starter relay fails as well, not unheard of. Is there a "click" when you press the starter button on the right handlebar? Click sound is...
    Post by: mastergregor, Sep 3, 2013 in forum: Mechanics Garage
  10. mastergregor
    Post

    Rear axle nut

    Good way to loosen up loctite or thread locker is to heat up the nut itself to something in the ~160-180F. Good heat gun will do. Then use a long...
    Post by: mastergregor, Aug 9, 2013 in forum: 5th Generation 1998-2001
  11. mastergregor
    Post

    Clutch troubles 95 VFR750

    Hm, I guess different strokes for different folks. I never had any issues with brake cleaner affecting seals on anything built after 1980. Carb...
    Post by: mastergregor, Aug 7, 2013 in forum: Mechanics Garage
  12. mastergregor
    Post

    Clutch troubles 95 VFR750

    While you are at it, you may want to pull apart the slave cylinder as well. Over time, with fluid not being changed, coat of rust forms and...
    Post by: mastergregor, Aug 6, 2013 in forum: Mechanics Garage
  13. mastergregor
    Post

    Regulator and Rectifier Replace

    Hm, steel has much more resistance than both copper and aluminum, so I really doubt it is used as a conductor ....... anywhere :confused:
    Post by: mastergregor, Jul 28, 2013 in forum: 5th Generation 1998-2001
  14. mastergregor
    Post

    Will Rear Brake Pads Fit the Front Calipers?

    I have 1998 VFR, and I have changed all the brake pads in all the calipers, both front and rear. I have used EBC 261 HH. These pads will fit...
    Post by: mastergregor, Jul 28, 2013 in forum: Mechanics Garage
  15. mastergregor
    Post

    Clutch Throw Almost Nothing

    You could get by without pulling any plastics, but I would remove left fairing, since it will be easier to work on the slave cylinder. The only...
    Post by: mastergregor, Jul 18, 2013 in forum: Mechanics Garage