Replace Lower Triple Clamp?

Discussion in 'Mechanics Garage' started by Alex_2000Yellow, Oct 2, 2024.

  1. Alex_2000Yellow

    Alex_2000Yellow New Member

    Country:
    United States
    Joined:
    Oct 2, 2024
    Messages:
    6
    Likes Received:
    1
    Trophy Points:
    3
    I fear I substantially over-torqued my lower triple-c when adjusting forks to stock height using an unfamiliar torque wrench. After which, I loosened and haven't touched it. Should I think about replacing the lower triple for fear of damage?

    Any thoughts welcome.
     
    Last edited: Oct 2, 2024
    Alex_2000Yellow, Oct 2, 2024


    This site may contain affiliate links for which VFRworld may be compensated
    #1
  2. RllwJoe

    RllwJoe Insider

    Country:
    United States
    Joined:
    Feb 2, 2017
    Messages:
    1,212
    Likes Received:
    350
    Trophy Points:
    128
    Location:
    Western Lower Peninsula, Michigan
    Map
    How "substantially over-torqued"? Do you recall the setting, and did you reach that point?

    BTW welcome to VFRW. When you have a chance post an intro of yourself and your 5th gen in the "Introductions" thread.
     
    RllwJoe, Oct 6, 2024


    This site may contain affiliate links for which VFRworld may be compensated
    #2
  3. Alex_2000Yellow

    Alex_2000Yellow New Member

    Country:
    United States
    Joined:
    Oct 2, 2024
    Messages:
    6
    Likes Received:
    1
    Trophy Points:
    3
    Thanks RllwJoe, I'll be post an introduction.

    The service manual has those at 36 ft-lbs (setting I used) but never clicked around there comparing to an earlier torque wrench I was using on something else. Felt closer to 50 lbs, but hard to say for sure.
     
    Last edited: Oct 6, 2024
    Alex_2000Yellow, Oct 6, 2024


    This site may contain affiliate links for which VFRworld may be compensated
    #3
  4. mello dude

    mello dude Administrator

    Country:
    Romania
    Joined:
    Jan 3, 2006
    Messages:
    4,357
    Likes Received:
    429
    Trophy Points:
    113
    Location:
    Southwest Ohio
    Map
    Are the threads stripped?

    Yes, please do an introduction post.

    Best Wishes
     
    mello dude, Oct 7, 2024


    This site may contain affiliate links for which VFRworld may be compensated
    #4
  5. Alex_2000Yellow

    Alex_2000Yellow New Member

    Country:
    United States
    Joined:
    Oct 2, 2024
    Messages:
    6
    Likes Received:
    1
    Trophy Points:
    3
    Hey mello dude, I don't believe the threads are stripped.
    Got an introduction post up :)
     
    Alex_2000Yellow, Oct 7, 2024


    This site may contain affiliate links for which VFRworld may be compensated
    #5
  6. mello dude

    mello dude Administrator

    Country:
    Romania
    Joined:
    Jan 3, 2006
    Messages:
    4,357
    Likes Received:
    429
    Trophy Points:
    113
    Location:
    Southwest Ohio
    Map
    Ok...since threads are not stripped....start over low, go slow and sneak up on the correct torque.
    That means mbe in steps mbe go 15,20,30 and final. Each bolt at each step of torque setting.
    Also, it's probably a good idea to get new bolts....
    Then get a different torque wrench that you trust!
     
    Last edited: Oct 8, 2024
    mello dude, Oct 7, 2024


    This site may contain affiliate links for which VFRworld may be compensated
    #6
Related Topics

Share This Page