Shorter License Bracket?

Discussion in 'Gear & Accessories' started by Guest, Jan 1, 2003.

  1. Guest

    Guest Guest

    I'm a brand new rider in reference to the VFR, been running a Big Bore Harley for the last year, just needed a change and my neighbor turned me on to this particular bike. Anyway, need to shorten my license plate bracket. Is there a shorter license plate bracket available? And, if so, where can I pick it up? Thanks.
     
  2. icw70

    icw70 New Member

    Joined:
    Jan 2, 2003
    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    Buffalo, NY
    I'm not sure if anyone sells them, if anyone finds out, let me know.


    I received the suggestions from this fellow.

    http://www.geocities.com/veefer800canuck/

    Here's how to do it yourself. I haven't done this yet, but received this from0-remove seat
    1-remove wiring for plate light under seat.
    2-remove plate and bracket. Separate same. Remove bracket mounting
    grommets from fender.
    3-separate the light assembly from the plate bracket. Save light and
    special retaining nuts (2).
    4-toss the bracket as far as possible. You should feel muuuch better now.
    5-remove red reflector from underneath the taillight. Toss reflector also. 6-using your license plate as a straightedge, align the top edge of the
    plate with the horizontal crease near the upper part of the fender, just

    below where the red reflector used to live. Use your judgement. Fake it. 7-scribe a pencil mark along the bottom edge of the plate, all the way
    across the fender.
    8-cut along pencil line carefully using a jigsaw and a fine tooth blade. 9-for the L&R sides of the fender, use a small soup can and align the
    curvature of the can's top with the edges of the fender and pencil in
    ~1/4 of a curve to round off the pointy edges left when you sawed off the
    lower portion of the fender. Puncture soup can and place on hot engine
    block for later consumption. Don't forget the crackers. 10-use a hand sanding block and medium grit sandpaper to gently smooth
    and chamfer the cut edges. Go slow and be picky and you'll have a beauty

    job with nice straight lines and flowing curves that blend with the
    sides of the fender.
    11-hold license plate back in position as in step 6, make sure it's
    centered nicely left to right and exactly level with that upper crease
    on the top part of the fender and mark your 2 upper bolt holes for the
    plate. DON'T DRILL THEM YET!
    12-now run and fetch the plate bracket from wherever it landed and
    somewhere (I forget) on the original bracket-to-fender mounting points,
    there should be a couple of "sleeved washers" (for lack of a better
    term) that fit into some rubber grommets. Get these. Toss bracket again. 13-find a drill bit the same O.D. as the sleeves. Now drill the holes.
    14-grind down the sleeved portions of the funny washer thingys until the
    sleeves are the same thickness as your fender and they should just fit
    in through the backside of the fender (washer part facing the tire).
    The sleeves should be just flush with the fender on the outside. This
    will provide some backing for the nuts when tightening and sandwich the
    fender nicely so as not to stress the plastic. I think it might crack
    later on down the road from vibration if one just bolted through the
    fender with no reinforcement. Or, maybe I just like futzing with things. 15-in the original license plate scheme, there was a little conical
    "rubber baby buggy bumper" that sat behind the centre bottom of the
    plate to keep it from vibrating. Grab that little sucker (wherever it
    has landed) and wiggle it out of it's hole. Drill similar hole at the
    botton centre of your fender, about 1/2 to 3/4" from the bottom edge of
    the fender. Hold up the plate and fuss with the location of the buggy
    bumper until you are happy, then mark and drill. Insert baby bumper in
    said hole.
    16-install plate with suitable bolts and nuts (I used some black,
    shouldered M6 bolts I had laying around) and tighten. It should be snug
    against the rubber bumper. If you're paranoid, use Nylock nuts. 17-examine the back of the plate light and drill suitable holes (where the

    red reflector used to live) for the two mounting studs as well as the
    backside of the bulb socket and associated wires. The back of the bulb
    socket will protrude slightly through the fender underneath the seat.
    Some trimming with a Dremel or a hobby knife may be required for optimal

    fit. Take your time, test and check fit. Ideally, the flared bottom edge

    of the plate light will be perfectly flush with the ridge in the fender
    above the license plate. Confused yet? Good.
    18-thread wiring thru hole and install light. Attach with the (2) special
    nuts.
    19-hook up plate light wiring and secure excess wire.

    Take it easy :)
     
  3. rshimmel

    rshimmel New Member

    Joined:
    Jan 4, 2003
    Messages:
    105
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    Ventura, CA
    If anyone has tried this on an 02 VFR, I'd love to hear about it. I'm dying to cut that thing off... ???
     
  4. fyeguy

    fyeguy New Member

    Joined:
    Mar 9, 2003
    Messages:
    11
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    Raleigh, NC
    Rick,

    I'm not sure if you know this or not, but you can completely remove the rear fender and leave the metal bracket for the plate and the light in place. Remove the rear fairing, then unbolt the fender... disassemble and then put it back together sans the humungous plasting fender.

    PS. Make sure you put the plate bracket back on the bottom holes... if not you'll be melting the plastic onto your trick-under-seat exhaust.
     
  5. rshimmel

    rshimmel New Member

    Joined:
    Jan 4, 2003
    Messages:
    105
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    Ventura, CA
    Yeah! I ended up doing this--removed the rear fender entirely, then remounted the license plate light and plate onto the metal support bracket...The only wrinkle was that I have the OEM hard bags and the metal hangars for the bags tie into a replacement (heavier) metal bracket that goes on in place of the old one, but once you've figured out the three points of attachment for the hangars, removing that rear fender gives the back end of the bike a much cleaner look. I had to trim the upper corners of the plate down a little to fit between the mufflers, and I've picked up a hugger to finish off the rear wheel but haven't put it on yet. Fun stuff. 8) When I can, I'll post pictures..
     
  6. VifferChic

    VifferChic New Member

    Joined:
    Mar 21, 2003
    Messages:
    89
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    Springfield, MO
    Please post your pics as soon as you get some. I'd love to see them.
     
  7. ScootR

    ScootR New Member

    Joined:
    Mar 17, 2003
    Messages:
    16
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    Boerne, Texas
  8. ScootR

    ScootR New Member

    Joined:
    Mar 17, 2003
    Messages:
    16
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    Boerne, Texas
  9. Guest

    Guest Guest

    I was browsing a Dennis Kirk catalog and they also sell the kit for 144.00. Kinda pricey, but also another option.
     
  10. waldrm

    waldrm New Member

    Joined:
    Jan 29, 2003
    Messages:
    229
    Likes Received:
    1
    Trophy Points:
    0
    Location:
    SE North Carolina
    Go to Cyclemall and check out the stealth tail. Since the VFR does not need turn signal mounts, this is a good option at $50.00. I binned by rear fender completely and went with an undertray; used a $9.00 mount from a 750 Nighthawk for the license plate. Email for pics
     
  11. waldrm

    waldrm New Member

    Joined:
    Jan 29, 2003
    Messages:
    229
    Likes Received:
    1
    Trophy Points:
    0
    Location:
    SE North Carolina
    Go to Cyclemall and check out the stealth tail. Since the VFR does not need turn signal mounts, this is a good option at $50.00. I binned my rear fender completely and went with an undertray; used a $9.00 mount from a 750 Nighthawk for the license plate. Email for pics. Agree with you on the Harleys being a big bore.
     
  12. mtradtke

    mtradtke New Member

    Joined:
    Nov 5, 2003
    Messages:
    11
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    Republic, Missouri
    I just took the stock license plate "mega mount" off of my '02 VFR, it looks 100% better than stock!! I just recently found this web site, and it is awesome! Keep up the excellent work. ;D
     
  13. floorguy724

    floorguy724 New Member

    Joined:
    Nov 18, 2003
    Messages:
    6
    Likes Received:
    0
    Trophy Points:
    0
    I Just took the shibang off, I had some metal brackets (metal strips w/holes in it) laying around and BAM!!! I figure the tail will produce enough light. Haven't had any problems yet. as he knocks on wood


    [​IMG]
     
Related Topics

Share This Page