Recent Content by deanc

  1. deanc
    Post

    Bike Shakes/Vibrates at low speed Braking...?

    Hmm, off the top of my head here are some things to check: Warped rotors? - check this by putting a rotor down on a known-flat surface like a...
    Post by: deanc, Jun 27, 2011 in forum: Mechanics Garage
  2. deanc
    Post

    Rebuilding camshaft gear drives - is it possible?

    Industrial supply house or industrial place that specializes in bearings will be much cheaper than the dealer & provide the same part (probably...
    Post by: deanc, Jun 27, 2011 in forum: Mechanics Garage
  3. deanc
    Post

    Strange noise, time to change the chains?

    There should be no "uneven movement" at all when rolling the rear tier with the bike on the centerstand. Hard to tell without seeing it in-person,...
    Post by: deanc, Jun 27, 2011 in forum: Mechanics Garage
  4. deanc
    Post

    Working on the back of the bike - what's the trick?

    Zowie it's like the Batcave...
    Post by: deanc, Jun 14, 2011 in forum: 3rd & 4th Generation 1990-1997
  5. deanc
    Post

    Working on the back of the bike - what's the trick?

    Wow, even cooler than the jackstands.
    Post by: deanc, Jun 13, 2011 in forum: 3rd & 4th Generation 1990-1997
  6. deanc
    Post

    3rd generation replacement rotors...

    Does anyone know whether the 4th gen rotors will bolt in? They have the same bolt pattern and AFAIK are the same diameter... not sure of the...
    Post by: deanc, Jun 13, 2011 in forum: Mechanics Garage
  7. deanc
    Post

    Working on the back of the bike - what's the trick?

    Or there's always the poor man's rear wheel stand... couple of jackstands and an old axle or other metal rod...
    Post by: deanc, Jun 9, 2011 in forum: 3rd & 4th Generation 1990-1997
  8. deanc
    Post

    Dwell Tachometer for Carburator Synch Job

    ++ on what the other posters have said - a "Dwell" tachomter is used for adjusting old-style points -type ignitions. Contrary to what the manual...
    Post by: deanc, Jun 9, 2011 in forum: 1st & 2nd Generation 1983-1989
  9. deanc
    Post

    Cooling Modifatios Done

    On my 3rd gen - I used Water Wetter, a lower-temp t-stat switch (from a mid-80's Honda car, don't recall which one), swapped the oil cooler for a...
    Post by: deanc, Jun 6, 2011 in forum: 5th Generation 1998-2001
  10. deanc
    Post

    need pilot mixture screws

    DiscountHondaParts.com, Honda, Polaris, KTM, Ski-Doo, Motorcycle, ATV,Snowmobile, Parts and Accessories.
    Post by: deanc, Jun 1, 2011 in forum: 1st & 2nd Generation 1983-1989
  11. deanc
    Post

    WTB Fairings for 93 VFR

    Don't have a tail faring for you - you might check the British and German ebay sites. VFR's sold a lot better over there than in the US. eBay -...
    Post by: deanc, May 31, 2011 in forum: 3rd & 4th Generation 1990-1997
  12. deanc
    Thread

    install electric speedo on 3rd gen?

    Hey everyone - I'd like to install an electric speedo (the gauge, not the underwear) on my 3rd gen - which has a mechanically-driven gauge in...
    Thread by: deanc, May 31, 2011, 0 replies, in forum: Mechanics Garage
  13. deanc
    Media

    stadium

    My RWB 3rd gen project
    Uploaded by: deanc, May 31, 2011, 0 comments, in category: 3rd Generation 1990-1993
  14. deanc
    Media

    night-front-right

    My RWB 3rd gen project
    Uploaded by: deanc, May 31, 2011, 0 comments, in category: 3rd Generation 1990-1993